How to oil grandfather clock video

how to oil grandfather clock video

How to Oil a Clock

Sep 16,  · Make sure your clock stays running. About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy & Safety How YouTube works Test new features Press Copyright Contact us Creators.

The mainspring is the heart of the timekeeping of any spring drive clock. If the mainspring is not oiled properly the clock will not work. The oil that is used is absolutely critical ; it must be able to work in a slow moving environment and it must be able to resist evaporation for many years.

It is also very important that the oil be absolutely non corrosive. In my opinion the mainspring grease that is available through the various suppliers is probably the best to use. How to remove ink from t shirt this situation exists in the time mainspring then the clock will not keep time and may not even run at all.

Mainsprings in the older clocks that have been around for many years have a buildup of hardened oil that is not removed by the ultrasonic process. This must be removed, or the clock will not work. The mainspring will stick erratically and cause timekeeping problems, and may actually bind up and release suddenly and cause a tooth on the spring barrel to be bent or even bend a tooth on the second wheel. If this happens when no one is there to hear the spring snap, then you will be befuddled when the thing just stops working after a careful overhaul.

I have used steel wool on mainsprings; have also tried very fine emery paper or crocus cloth. The problem with using emery paper is that extreme care must be taken to remove all of the residue from the cleaning with the emery paper or the mainspring will be worse that it was before it was cleaned. After the mainspring has been cleaned and polished, if you ,a clean soft light colored cloth can be used to remove the residue; then run the spring through the ultrasonic cleaner. Levers that are attached to sleeves that ride on shafts should not be oiled : particularly those levers that depend on gravity to operate.

The reason for this is that when the oil thickens up slightly the lever will not drop every time; or it will drop too slowly. A classic example how to start a small jewellery business the count arm, or the rack as it is sometimes called. It will work just fine at first: then after several months the oil will thicken and the common complaint is: the clock only strikes 1 sometimes.

If you feel you must oil the lever ; be sure that it is what happens to blood as it circulates the thinnest possible film; and. The more oil the more the chance of a problem. If oil is placed on brass gears gear teeth in a slow moving gear train, the gear teeth will very likely be destroyed in several years. This applies particularly in the area of how to remove programs from hard drive higher power gears ; the main and second wheels.

The clock oil that is available through the suppliers that is made specifically for clocks is the only typein my opinionto use. The synthetic oil that is designed for brass on brassbrass on steel and steel on steel is the best. Do not use wdever. It is a good lubricantbut not for clocks. It thickens up rapidly and will add enough friction to stop the clock in a few months.

Be sure that oils are not mixed ; often the combination of two oils can cause chemical reactions that will corrode the steel pivots. Avoid oiling cuckoo clock mechanism levers whenever possible. The majority of these mechanisms use gravity to make the levers drop. An excessive amount of oil on a trip leverfor example, can cause it to fail.

How much oil is too much? If the oil is running out of the oil cup then it is too much. If there is no substantial oil cup then only oil enough to fill the space between the bushing and the pivot.

Oil the hand clutch so the hands move smoothly when setting the time on the clock. Do not oil moon dials. Do not oil calendar mechanisms. You always want to use a non-migrating, synthetic oil for grandfather clocks and other mechanical movement clocks. Skip to content How to Oil Your Clock Mainsprings: The mainspring is the heart of the timekeeping of any spring drive clock. Levers: Levers that are attached to sleeves that ride on shafts should not be oiled : particularly those levers that depend on gravity to operate.

Thanks for the heads up.

Post navigation

Grandfather clocks are a handsome compliment to home decor. Though the clocks look nice even when non-functional, a working clock mechanism is impressive and increases the value of the clock. If your clock runs slowly or stops in between inspections, you can use a little oil to lubricate the internal gears. Step 1 Stop the clock. Step 2. How to properly oil a clock The first step in oiling or servicing your Grandfather clock is to make sure you use gloves at every stage. I personally use cotton gloves when handling any wood parts of the clock and I use latex gloves when handling any brass or metal parts. Apr 27,  · Oil and dust buildup will happen within the gears and mechanisms inside the grandfather clock. It requires a professional to disassemble the inner workings, clean them and put them back together. If you attempt to clean the mechanisms of your grandfather clock yourself, you will void the warranty and risk breaking the clock.

Just like regular oil changes extend the life of your car's engine, regular clock oiling extends the life of your clock. Oiling your clock every two years will prevent expensive clock repairs and ensure that your clock will last for the generations to come. Imagine never changing your car's oil; it wouldn't take long for the engine to seize. Without regular oiling your clock will end up requiring a major service, or possibly a new movement.

For those interested in learning how to oil a clock, this tutorial will show you how it is done. The most important thing to remember is to ensure that you only use high quality clock oil. Many professionals use synthetic oil but there are numerous high quality non-synthetic clock oils.

The main thing to be cognizant of when choosing clock oil is to ensure it is designed to be used in clocks. Synthetic clock oil is not cheap because it is specifically formulated for the metals used in clocks. Brass and steel are used in clocks because when properly lubricated with the right oil it forms a perfect bearing. Using oil designed for hard metals or containing additives like graphite will actually cause harm to the brass clock plate and lead to premature aging and wear.

All mechanical clocks can and should be oiled. However the ease of oiling and frequency of oiling depends upon several factors. The age and type of clock are the main two factors. Most grandfather clocks have access panels on the sides or have the ability to remove the hood which exposes the movement. Modern grandfather clocks usually have more complicated movements which makes reaching all the oil points a little more difficult. Table or mantle clocks have smaller movements which also makes reaching all the oiling points more complicated.

Generally, removing the movement from the clock will make oiling easier and we always recommend removing the movement and dial before oiling. Because we are experts in antique grandfather clocks, let's talk about an antique grandfather clock. For the purpose of this article, we are simplifying the process.

However, the process outlined below should generally describe how to remove most movements. First, you will need to remove the clock hood. Never attempt to remove the hood without at least one weight being in place. The hood of most grandfather clocks is removed by sliding it forward.

Before sliding the hood forward secure the glass door to prevent it from opening while removing the hood. Next, remove the time side right weight and then remove the pendulum from the crutch. Because in some grandfather clocks the movement is held in place by the downward force of the weights, when you remove the strike side left weight the movement is susceptible to falling. While you unhook the last weight keep pressure on the weight cable, then remove the movement.

After removing the hood and weights you will be able to remove the movement from the clock. Clock movements are generally secured to the clock with screws but many older British grandfather clock movements are not fastened at all. Once the screws are removed the movement should just lift out of the clock with the clock dial attached.

Once the movement is removed you will remove the clock hands. Remove the nut or pin that holds the hands in place by gently holding the minute hand.

Once the nut or pin is removed gently remove the minute hand. Sometimes it will stick and a gentle rocking back and forth will loosen the hand and it will come off. Next you will need to remove the hour hand by gently pulling on the base of the hand and again gently rocking it back and forth until it comes off. The first step in oiling or servicing your Grandfather clock is to make sure you use latex gloves when handling any brass or metal parts. There is acid in the oils of our fingers and this acid eats through the thin layer of lacquer when it comes in contact with brass.

Now that the movement is free from the case you will notice multiple oil sinks on the surface of each clock plate. Oil sinks are located where the ends of the steel arbor meet the clock plate. In-between the two clock plates are all the clocks gears. These gears are held in place by a steel arbor that is pressed into the clock plate. As the gear turn the steel arbor rotates around while the clock plate remain stationary. Without oil friction will eventually cause the hole in the clock plate to enlarge and become elongated.

This happens because brass is a softer metal than steel and the downward force of gravity will cause more wear on the bottom side of the clock plate. When the hole that holds the steel arbor in place becomes enlarged the clocks gear will not turn correctly and will eventually cause the clock to stop working. To oil a clock apply one drop of oil to each oil sink.

It is best to use a clock oiling pen or a bottle with a long needle. This will make it easier to apply a single drop to each oil sink. Don't try and fill the oil sink, because the oil is held in place by surface tension.

If you apply too much oil, the surface tension will not hold and the oil will run down the plate, leaving the bearing dry. Repeat the oiling process for all oil sinks on both the clock plates.

Don't forget to oil the weight pulleys and the front plate posts. TickTockTony sells clock oil that is specially manufactured for clocks. Every order comes with 15cc's of high quality synthetic clock oil in an oil syringe needle which is pictured above.

The stainless steel needle is 3. To purchase the clock oil using PayPal's secure servers, click the button below. Unfortunately we do not ship outside the United States. We have created the video below showing how to oil a clock's movement. Visit our YouTube channel to watch more videos. There you will find numerous tutorials covering topics like how to remove a clock's movement from the case, how to remove a clock's dial, and how to adjust a clock's beat.

1 thoughts on “How to oil grandfather clock video

Add a comment

Your email will not be published. Required fields are marked *