How to Install Interior Wooden Balusters
Aug 30, · Pinpoint the spots where the banister connects to the spindles and posts. Unscrews any screw fasteners or remove the nails that are securing the top of the spindles to the bottom of the railing. Shift your attention to the posts on either end Estimated Reading Time: 8 mins. Measure the spaces between the balusters and cut enough filet pieces to fit between each baluster. Apply glue to each one and fit them into the channel between the balusters.
Interior balusters are the spindles that support the handrail. This type of system is built in four parts designed to fit together. The bottom rail has holes drilled at specific intervals that receive a dowel on the end of the baluster. The top rail has a channel that receives the square end of the baluster. Small pieces of wood, called filets, are installed between the balusters at the top to finish and provide stability to the balusters. Measure the distance between newel posts.
Cut the bottom rail and the handrail at the measurement, using a miter saw. Place the bottom rail between the two newel posts and tap it down tightly. Place glue into the hole. Place glue into the holes on the bottom rail that receive the dowels on the bottom of the balusters. Place the balusters into the holes one at a time, fitting the dowel on the bottom into the holes.
Fit the handrail into place. There is a channel that fits over the square top of the baluster. Place one filet between each baluster at the top. Filets are thin, rectangular pieces of wood that come with the system and act as fillers and spacers for the balusters. Tap them in, using a hammer. Shoot one pin nail horizontally through the lip at the bottom of the handrail and into the top of the each baluster. Shoot one pin nail up vertically through each filet. Place glue and furniture buttons into the holes.
Putty the nail holes with wood dough, using a putty knife. Allow the putty to dry, then sand the areas lightly, using grit sandpaper. Paint or finish what are extraneous variables in nursing research stain and lacquer.
Specializing in hardwood furniture, trim carpentry, cabinets, home improvement and architectural millwork, Wade Shaddy has worked in homebuilding since Shaddy has also worked as a newspaper reporter and writer, and as a contributing writer for Bicycling Magazine. By Wade Shaddy. Related Articles. Tips You can also paint or stain the system before installing it. Use a putty crayon to fill nail holes after installation. If your stair rail system doesn't come with holes in the bottom rail, it will have a channel at the bottom, just like on the handrail.
Use filets on the bottom rail just like on the top for this type of installation. If some what is a prusik minding pulley your filets are too tight, trim them with a miter saw. Because you're using filets and predrilled holes, it means that typically, you don't need to level and straighten your balusters, but you should check each one with a level to ensure it is straight.
If you need to make adjustments, do it before any glue is added. Wear safety glasses.
Last Updated: December 3, References. To create this article, volunteer authors worked to edit and improve it over time.
There are 8 references cited in this article, which can be found at the bottom of the page. This article has been viewed 35, times. Learn more A banister provides additional safety on your staircase and visual appeal to a home.
With the use of some wood and a few tools and supplies, you will be able to install a banister. The following is a guide on how to install a banister. Log in Social login does not work in incognito and private browsers.
Cookie Settings. Learn why people trust wikiHow. Download Article Explore this Article Steps. Tips and Warnings. Things You'll Need. Related Articles. Purchase a banister at a home-improvement store or on the Internet. Determine the correct height for the banister. Mark the wall adjacent to the top and bottom stairs with the correct height. Stand a level vertically to ensure the accuracy of your markings.
Connect the markings with a chalk line. Locate the studs in the walls. Cut a piece of wood that fits the bottom of the banister. Screw the mounting strip onto the wall. Apply painter's tape to the areas of the wall that are near the mounting strip. Stain the mounting strip. The color should match the banister. Be sure to apply 2 coats of stain. Cut the banister to fit the staircase.
Measure the total amount of wood that you will need to fit the staircase. Use a power saw to cut the banister. Miter the ends of the banister.
Use a miter box to do so and follow the instructions that apply to the brand that you choose. Apply the banister to the mounting strip. Mark evenly spaced areas on the painter's tape that you will use to screw it in. These should not coincide with the holes that you drilled for the mounting strip. Screw the banister into place. Miter a cap for each end of the banister. Glue them into place. Screw them into place to ensure that they remain sturdy. Install pre-cut wooden pegs into the holes on the banister.
Be sure that they match the color of the banister. Gently use a hammer to secure the pegs into the banister. Include your email address to get a message when this question is answered. By using this service, some information may be shared with YouTube. Instead of using a miter box, you may use a table saw or power saw.
Helpful 0 Not Helpful 0. Submit a Tip All tip submissions are carefully reviewed before being published. Related wikiHows How to. How to. Co-authors: 7.